Accortec JNP100GAOC1M-ACC QSFP28 100-GE ACTIVE OPTICAL CABLE JUNIPER

Accortec

JNP100GAOC1M-ACC - Juniper Compatible QSFP28 100G Active Optical Cable | 1 M | TAA Compliant

The AccortecJNP100GAOC1M-ACC is a 1-meter QSFP28,100-Gigabit Active Optical Cable (AOC) engineered for plug-and-play compatibility with Juniper Networks equipment. Delivering 100 Gbps aggregated bandwidth via four bidirectional 25 Gbps lanes over 850 nm multimode fiber (OM3/OM4), it offers unmatched low-latency performance in modern data center and HPC deployments. Hot-swappable and factory-programmed for Juniper switch and routing platforms, this active cable helps reduce cabling complexity while preserving enterprise-grade integrity and efficiency.

Features

Built to function as a direct OEM-compatible replacement for Juniper's JNP-100G-AOC-1M, this Accorteccable supports enterprise interconnects between switches, routers, servers, and storage nodes. Its active fiber design enables longer reach than passive copper DACs combined with less power consumption per link (typically < 3.5 W per end)

Advanced Options

The QSFP28 connectors ensure high-density port deployment, while the lightweight multimode fiber cable offers superior EMI immunity and excellent airflow management in densely packed racks. Embedded diagnostics support (DDM/SFF-8472) and MSA compliance facilitate real-time monitoring and interoperability. Fully compatibility-tested with Juniper platforms, this cable supports seamless integration and rapid network scaling with no vendor lockout risks

Product Key Features

• QSFP28-to-QSFP28 100Gbps Active Optical Cable(AOC)

• Factory-programmed for Juniper JNP-100G-AOC-1M compatibility

• 4 × 25 Gbps full-duplex lanes (total 100 Gbps) over OM3/OM4 multimode fiber

• Low power consumption (< 3.5 W per cable end) with enhanced EMI immunity

• Hot-swappable plug-and-play installation

• Lightweight, flexible LSZH jacket with small bend radius

• Digital diagnostics monitoring (DDM) support and RoHS compliant

---

Reliability & Performance

The AccortecJNP100GAOC1M-ACC delivers enterprise reliability with consistent throughput and secure optical connectivity. The active optical transducer design reduces heat generation and eliminates the need for intermediate copper or active transceivers, enhancing rack density and airflow efficiency. With support for 0 °C to 70 °C operating temperature, the cable is robust for most data center setups Its MSA-compliant QSFP28 connectors and factory-embedded Juniper-compatible firmware ensure installation reliability and accurate vendor recognition, despite being a third-party product. Real-time monitoring via DDM allows visibility into transmit/receive levels, temperature, and voltage. With a flexible 3 mm diameter LSZH jacket and a small minimum bend radius (~25 mm), it's practical for tight cable runs in high-density switch environments

Key Features (Bullet List)

• QSFP28 to QSFP28 Active Optical Cable (100 GE)

• 1 Meter Length

• Juniper JNP-100G-AOC-1M Compatible

• 4 × 25 Gbps Lanes (100 Gbps)

• 850 nm Multimode Fiber (OM3/OM4)

• Low Power (< 3.5 W per end)

• Hot-Swappable, Plug-and-Play

• Digital Diagnostics Monitoring (DDM)

• LSZH Jacket, 3 mm Diameter, 25 mm Bend Radius

• RoHS / MSA Compliant

Specifications :

Product Specifications

Specification	Description
Model Number	JNP100GAOC1M-ACC
Cable Type	Active Optical Cable (AOC)
Connector Type	QSFP28 to QSFP28
Data Rate	100 Gbps (4 × 25 Gbps lanes)
Cable Length	1 Meter
Wavelength	850 nm
Fiber Type	Multimode (OM3/OM4)
Power Consumption	Typically ≤ 3.5 W per cable end
Operating Temp Range	0 °C to 70 °C
Jacket	LSZH, 3 mm diameter
Min Bend Radius	~25 mm
Diagnostics	Digital Diagnostics Monitoring (DDM/SFF-8472)
Compliance	MSA Compliant, RoHS